The author is making several good observations regarding A Step-by-Step Guide to Installing a Bathtub in general in the content down below.
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old tub with a new one is additionally a reasonably difficult task. If the old tub is conveniently obtainable, the task can relocate easily; if you have to open up a wall to get rid of the old tub and also place the brand-new bathtub, the task is much harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to vacate the old bathtub and set in the brand-new one. Make sure you have actually qualified on your own for the work as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed task, it is much better to consider employing one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already acquired a new tub and also don't need to change the plan of your previous water supply pipelines.
Your tools and material checklist should make up the following:
Preparing for the Installation
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be rather bothersome because of the limited access that is often the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipes. When the supply pipes have been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub up until the spirit level reads degree.
To install taps, fit the bottom of the outermost versatile tap connector to the suitable supply pipe by making a compression sign up with; then do the exact same for the other tap.
Turn on the supply of water as well as examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally check the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and securing around the bath tub ought to wait up until the bathtub has been utilized a minimum of once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and also the sink. Secure the faucet in position with the maker provided backnut. Once the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind must be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, resulting in complications with moisture and feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your components and also installations. They are sold in tubes and also cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the motion experienced when the tub remains in use. The sealer can split relatively early if you do not think about this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very fascinated by Tools You Need to Install a New Bathtub and I'm hoping you appreciated the new blog post. Loved our write up? Please share it. Let somebody else check it out. Thank-you for taking the time to read it.
Check Us Out